Beretta 92 Match Hammer
The Beretta Match Hammer is a DLC coated gunsmith-fit replacement for your existing 92 or PX4 hammer.
This upgrade reduces pre-travel in single action to less than 2MM of travel - combined with our Optimized Performance Trigger Bar, your single action pull & reset will be short, smooth, and fast!
The Match Hammer MUST be used with either the LTT Optimized Performance Trigger Bar OR the Beretta Extreme S Trigger Bar AND the Match Hammer MUST also be installed either by LTT or another qualified gunsmith.
When combined with the LTT Trigger Job, the Beretta Match Hammer may cause your single action trigger pull weight to be lower than the standard 3.5# pull weight.
LTT accepts no liability for any damage or injury that results from failure to follow the above instructions.
Please Note: The Beretta Match Hammer will ship in Beretta Factory packaging with a SKU tag that reads "Skeletonized Hammer 92" with part number C5L047 - we assure you this IS the Match Hammer, and a part number search on Beretta's website will confirm this: https://www.berettausa.com/en-us/skeletonized-hammer-92-92x-perf/c5l047/
DISCLAIMER: We recommend that this product as well as all other firearms parts & kits sold by Langdon Tactical be installed by a competent pistolsmith. No liability is expressed or implied for ANY damage or injury which may result from improper installation or use of this product. Installation of any firearm parts may limit or void the manufacturers warranty. We strongly recommend that the safety and operation of your modified handgun be thoroughly checked by an accredited gunsmith prior to use.
5 Reviews Hide Reviews Reviews
So I definitely skipped over the part where it is stated that "the Match Hammer MUST be used with either the LTT Optimized Performance Trigger Bar OR the Beretta Extreme S Trigger Bar" and installed this hammer without changing the factory trigger bar on my M9A1. Well, luckily I had also ordered the LTT trigger bar because with the factory trigger bar and the match hammer my single action trigger pull wouldn't work! After installing the LTT trigger bar everything works as it should and so far I'm very happy with the result. Install of the hammer couldn't have been easier.
Excellent addition when accompanied with a Langdon Tactical Optimized Trigger Bar. Install was straight forward with end results being a very short and crisp single action pull and reset. I did have to remove/stone a minuscule amount of material from the LTT Optimized Trigger Bar where it contacts the Match Hammer single action contact surface to adjust for a tiny bit of extra single action pre travel as to bring the Beretta firing pin safety block into the correct spec/operation.
Installed into my Elite LTT 92 Centurion. If you're on the fence, I'm telling you to go for it. Very noticeable improvement. As someone fairly new to firearms, I wondered if it was something I would notice or if it was something for the more experienced. Well the improvement was absolutely appreciable.
The match hammer did exactly what Landon stated it would do, It made the SA take-up a memory. The SA trigger now has virtually no take-up. The SA trigger now has less take-up than my Apex Forward Set M&P trigger which is an incredibly good trigger. I also have the Langdon Optimized Trigger bar installed - together they make for an entirely new 92 trigger one that does not even resemble the stock trigger. Smooth DA, vey short reset, virtually no over-travel, and the bare minimum SA take-up. If I blindfolded someone and gave them a 92FS with D spring and had them operate the triggers on the 92 stock and the one with an upgraded tigger bar and match hammer, they would swear it is not the same gun.
If you buy an LTT with all the upgrades you will feel a great trigger and be impressed but if you incrementally upgrade a 92FS, as I have, then you will see the magic in every upgrade; it has been impressive. My 92 is now the best gun I own. It has the best trigger, the best looks, the best feel, and the greatest accuracy. And... I have a Landon Red Dot slide with a Holosun 507c-x2 mounted on it. You just cannot go wrong with what Langdon tactical offers. No I do not work for Landon - I am just impressed.
Dropped in my 92FS Compact without needing any additional fitting. Combined with the LTT Trigger bar and 13# spring my trigger is smooth and tight. DA 7lbs. SA 3.75lbs.